




配置和指标
?s1:实现选择输出信号的类型,pnp(p/2)或npn(n)。
?s2:分别根据npn或pnp选择(通过s1)实现选择内部pullup(pu)或pull-down(pd)电阻器。
?l1:通电时为绿色。
?l2:当常闭系列输出切换时为琥珀色(例如:全部触点打开)。
?l3:当切换常开系列时琥珀色(例如:全部触点闭合)。
?s1: enables the selection of the type of output signal, pnp(p/2)/npn (n).
?s2: enables the selection of internal pull-up (pu)/pulldown(pd) resistors depending on the npn/pnp selection(via s1), respectively.
?l1: green when powered.
?l2: amber when the nc series output is switched (e.g. allcontacts open).
?l3: amber when the no series is switched (e.g. all contactsclosed).

来自传感器的信号使用继电器开关或微处理器(基于控制箱的类型)进行调理,以便根据操作要求提供一个或多个输出。甚至可以使用跳线或选择器配置单个输出,从而定义类型(pnp或npn),以及常开(no)或常闭(nc)操作模式。传感器盒由框架、夹具和端子板组成,使传感器和输出的安装和接线简单方便。此外,采用的可复位熔断器保护整个电子设备避免短路。所有接线盒都有led警示灯,通过透明塑料容器可见,夹爪,便于排除故障和查看输入/输出状态。接线盒配有pg9电缆密封套(具体取决于型号),可---集成的电子电路板(sbxc、sb6b、sbf)的ip65防护等级,而非模块化结构(sbm)。这使得可以尽可能地---尺寸,并且将盒子直接固定至通常构成夹持器框架的铝型材上。

编程单个sb8f
在对传感器盒进行编程之前,电机夹爪,请---有线输入处于所需配置(开/关)以启用输出。按下autoset按钮并按住3秒钟,夹爪厂家,直到reading红灯开始闪烁,然后松开。红灯(reading)闪烁表示微处理器正在读取和存储全部输入的状态。然后红灯熄灭,启用了输出。黄灯(stored)指示启用输出。
before programming the sensor box, make sure that the wired inputs are in the confguration (on/off) desired to enable the output. press the autoset button&hold it down for 3 seconds until the reading red light starts fashing, then release it.the red light (reading) fashing indicates that the microprocessor is reading&storing the state of all the inputs. then the red light goes off&the output is enabled. output enabling is indicated by the yellow light (stored).

机械夹爪-夹爪-吉玛泰克自动化(查看)由吉玛泰克自动化工程(常熟)有限公司提供。吉玛泰克自动化工程(常熟)有限公司位于江苏省常熟市古里镇通华路1号2幢。在市场经济的浪潮中拼博和发展,目前吉玛泰克在气动工具中享有---的声誉。吉玛泰克取得---商盟,标志着我们的服务和管理水平达到了一个新的高度。吉玛泰克全体员工愿与各界有识之士共同发展,共创美好未来。
联系我们时请一定说明是在100招商网上看到的此信息,谢谢!
本文链接:https://tztz352373.zhaoshang100.com/zhaoshang/282004878.html
关键词: