sbms/sbms-e - 从模块
每个单独的从模块均可以连接单个传感器。它由内部总线连接（由主模块提供）供电，并触发两个固态继电器的换向：基于传感器输出的常开触点和常闭触点。两个选择器可用于配置传感器信号输出（pnp/2线或npn）和逻辑（正向或反向）。该模块还有两个用于诊断的led指示灯。
each individual slave module enables the connection of a singlesensor.
it is powered from the internal bus connection (provided by themaster module)&triggers the commutation of two solid staterelays: a no contact&a nc contact based on sensor output.
two selectors are available to conffgure sensor signal output(pnp/2 wires/npn)&logic (direct/reverse).the module also has two led indicators for diagnostics.
夹具订制
agg可在机械手和模具间提供精i准的中心。
注塑模具内金属嵌件安放时尤其要注意这一点。
夹具agg...b 安装在eoat上，西藏自治吸盘，钢管 agg...c 安装在模具上。
一旦机械手向模具靠近，夹具在压力的作用下逐步向钢管靠近，
并与之接触。
agg21-b 和 agg30-b 采用的是双动作安全弹簧，---在压缩空
气 (nc)缺失时设备的正常运行。
agg19-b 采用的是单动作复位弹簧(no)。
gripper for engagement
the agg is used to provide a precise ws=ing between the robot
and the mould.
this necessary when metal inserts must be p1aced in the
mould， before the p1astic injection.
the gripper agg…-b is fitted on the eoat，吸盘品牌， while the steel bushing
agg…-c is fitted on the mould.
once the robot has approached the mould， the gripper is
pressurized， thus it closes&engages the bushing.
agg21-b&agg30-b are double-acting with a safety spring to
keep the gripper engaged even without compressed air (nc).
agg19-b is single-acting with reset spring (no).
双钳口自动对准平行i气动钳夹 (sx系列)
?双动作 (可按需关闭)。
?高夹紧力。
?防护等级为ip67。
?列柱向上采用双层o型圈设计。
?适用于---的环境。
?可选的磁传感器。
?fda-h1 食品级润滑脂
?double acting (normally closed on request).
?high gripping force.
?protection class: ip67.
?double o-ring sealing on the columns.
?suitable for harsh environments.
?optional ---ic sensors.
?fda-h1 food-grade grease.
常熟吉玛泰克自动化(图)-气动吸盘-西藏自治吸盘由吉玛泰克自动化工程（常熟）有限公司提供。常熟吉玛泰克自动化(图)-气动吸盘-西藏自治吸盘是吉玛泰克自动化工程（常熟）有限公司今年新升级推出的，以上图片仅供参考，请您拨打本页面或图片上的联系电话，索取联系人：吴琦。
联系我们时请一定说明是在100招商网上看到的此信息，谢谢！
本文链接：https://tztz352373.zhaoshang100.com/zhaoshang/284372261.html
关键词：
滇公网安备 53011202000392号